Solenis + NCH:<br/>Forward As One
NCH is now part of Solenis
Close 686C6711-FB74-47F4-AFEE-14D0F9C09B39

Ten Principles of Hygienic and Sanitary Design in Food and Beverage Processing

Diversey Logo
By: Hein Timmerman | November 19, 2026 | Reading time: 7 minutes

Food safety starts with hygienic and sanitary design. From individual equipment components to complete processing lines and the surrounding production environment, hygienic design plays a fundamental role in preventing contamination and enabling effective and efficient cleaning and disinfection.

Hygienic design should be considered throughout the complete lifecycle of equipment: specification, design, fabrication, installation, commissioning, operation, cleaning, maintenance, modification and eventual replacement.

International organisations including EHEDG, 3-A SSI and ISO have developed guidance and standards to support the hygienic design of food-processing equipment and environments.

Hygienic design integrates food-safety risk management with engineering and equipment design to prevent contamination and enable effective, efficient and repeatable cleaning and disinfection.

 

1. Apply a Risk-Based Approach

Hygienic design starts with understanding the intended use of the equipment and identifying the associated food-safety and hygiene risks.

The assessment should consider the complete process and not only direct food-contact surfaces. Product-contact, indirect-contact and non-product-contact areas can all contribute to contamination or cross-contamination.

Relevant hazards may include:

  • Biological hazards: pathogenic and spoilage microorganisms relevant to the product, process and production environment.
  • Chemical hazards: allergens, residues of cleaning and disinfecting chemicals, lubricants and other process chemicals.
  • Physical hazards: metal fragments, plastics, glass, damaged elastomers, loose fasteners and other foreign materials.

The assessment should also consider whether the process is wet or dry, open or closed, the required hygienic level, cleaning method and the consequences of a hygienic-design failure.

Risk assessment should be documented and reviewed whenever equipment, products, processes or cleaning procedures change.

 

2. Design Surfaces to Be Cleanable

All relevant surfaces must be capable of being cleaned to the hygienic level required for their intended use.

Surfaces should therefore be smooth, continuous and free from cracks, pits, folds, crevices and other imperfections that can retain product, microorganisms or allergens.

For stainless-steel product-contact surfaces, Ra ≤0.8 µm is a commonly applied hygienic-design benchmark, although surface roughness alone does not determine cleanability. Surface geometry, fabrication quality, welds, defects and the properties of the soil are equally important.

Cleanability must also be maintained throughout the equipment lifecycle. Wear, corrosion, inappropriate grinding, poor repairs and mechanical damage can progressively create niches that are difficult to clean.

Equipment condition should therefore form part of routine hygienic-design inspection and preventive maintenance.

 

3. Select Suitable and Compatible Materials

Materials of construction must be suitable for their intended use and compatible with:

  • the food product;
  • processing temperatures and conditions;
  • cleaning and disinfecting chemicals;
  • mechanical cleaning methods;
  • the production environment; and
  • the expected equipment lifetime.

Food-contact materials should be non-toxic, non-absorbent and resistant to corrosion and degradation under their intended conditions of use.

Stainless steel is widely used because of its mechanical properties, corrosion resistance and cleanability. However, the appropriate stainless-steel grade must be selected according to the application. Plastics, elastomers, seals, coatings and other materials must similarly be selected according to food-contact, temperature, chemical and mechanical requirements.

Material selection should therefore be based on the complete operating environment rather than on a single generic material specification.

 

4. Ensure Effective Drainability

Equipment and its supporting structures should be designed to prevent unintended retention of product, water and cleaning or disinfecting solutions.

Surfaces should be sufficiently sloped and configured to allow liquids to drain effectively.

The required slope depends on the equipment geometry, surface characteristics and application; therefore, a single minimum slope should not be treated as universally applicable.

Particular attention should be given to:

  • vessel bottoms;
  • pipelines;
  • valve bodies;
  • equipment frames;
  • covers;
  • electrical enclosures;
  • horizontal structural members; and
  • areas where condensation may occur.

Poor drainability creates conditions in which microorganisms can survive or grow and may also promote corrosion and biofilm formation.

 

5. Provide Accessibility for Cleaning, Inspection and Maintenance

The equipment design must support its intended cleaning method.

Equipment intended for manual cleaning or Cleaning out of Place (COP) should provide adequate access to all surfaces requiring cleaning, inspection and maintenance.

Equipment intended for Cleaning in Place (CIP) must be designed so that cleaning solutions reach all relevant surfaces under the validated cleaning conditions.

Accessibility is equally important for hygienic inspection and maintenance. Components that cannot be adequately cleaned or inspected can become hidden contamination niches.

External equipment surfaces, frames, guards, control panels, cables, pipework and cleaning-system components must therefore also be considered in the hygienic-design assessment.

 

6. Use Hygienic Joints, Seals and Welds

Permanent joints in hygienically critical areas should preferably be continuously welded and designed to provide smooth, cleanable surfaces.

Welds should be free from hygienically significant defects such as:

  • cracks;
  • porosity;
  • undercut;
  • incomplete penetration;
  • excessive penetration;
  • cavities; and
  • unacceptable surface oxidation or heat tint.

Weld quality and inspection requirements should be defined according to the hygienic risk and intended application.

Where detachable joints are required, seals and gaskets must be correctly designed, installed and compressed so that they do not create crevices, product traps or areas that cannot be effectively cleaned.

 

7. Avoid Crevices, Dead Ends and Product Traps

Crevices and dead ends can retain product and cleaning solutions and reduce the effectiveness of cleaning and disinfection.

They should therefore be eliminated wherever reasonably possible.

Where branches, instrument connections, sample points or other dead-end configurations are unavoidable, their geometry and orientation should be designed to ensure effective product displacement, cleaning and drainability.

Cleanability should not be assessed solely from a simple dimensional ratio. Geometry, orientation, flow conditions, cleaning method and the properties of the product and soil all influence hygienic performance.

Connections for sensors and instrumentation should therefore be incorporated as an integral part of the hygienic design.

 

8. Eliminate or Hygienically Seal Hollow Structures

Hollow structures can become serious hygiene risks when product, water or cleaning solution enters them and cannot subsequently be removed.

Hollow equipment frames, rollers and structural members should therefore preferably be eliminated.

Where hollow construction cannot be avoided, it should be permanently and hygienically sealed against ingress, and the integrity of the structure should be maintained throughout its service life.

Fasteners, brackets, mounting plates, junction boxes, nameplates and similar components should be installed so that they do not create inaccessible gaps, cavities or moisture traps.

 

9. Prevent Cross-Contamination

Hygienic design extends beyond the equipment itself.

The complete production environment should be designed to minimise the movement of microbiological, allergenic, chemical and physical contaminants between areas, equipment and products.

Important considerations include:

  • hygienic zoning;
  • segregation of raw and processed products;
  • personnel and material flows;
  • drainage;
  • air movement;
  • water management;
  • equipment positioning;
  • cleaning activities;
  • allergen segregation;
  • lubricants and other ancillary substances; and
  • maintenance activities.

The design should avoid contamination from higher-risk to lower-risk areas and minimise the potential for cleaning activities themselves to spread contamination.

Hygienic equipment design and hygienic factory design should therefore be considered as one integrated system.

 

10. Design Cleaning into the Equipment — Then Validate, Verify and Monitor It

Cleaning should never be considered only after equipment has been installed.

The required cleaning method — CIP, COP, automated open-plant cleaning, manual wet cleaning or dry cleaning — should form part of the original hygienic-design specification.

Cleaning and disinfection procedures should define appropriate parameters such as:

  • time;
  • temperature;
  • chemical concentration;
  • mechanical action or flow;
  • sequence;
  • water quality; and
  • acceptance criteria.

The cleaning process should then be validated to demonstrate that it can consistently achieve the required hygienic outcome.

Once validated, appropriate verification and monitoring should demonstrate that the process continues to operate within the defined conditions and remains under control.

Hygienic design and cleaning validation are therefore closely connected: poorly designed equipment cannot reliably be compensated for by increasingly intensive cleaning.

 

Hygienic Design Supports Food Safety and Sustainable Production

Good hygienic design does more than reduce contamination risk.

Equipment that is easier to clean can potentially require less cleaning time, water, chemicals and energy while also reducing downtime and improving production availability.

Hygienic design therefore provides an important foundation for both food safety and sustainable manufacturing.

However, optimisation should never compromise the required hygienic outcome. Cleaning efficiency improvements should be introduced through a risk-based approach and supported by appropriate validation and verification.

 

Increase Your Knowledge of Hygienic Design

Diversey's hygienic-design expertise combines practical food-industry experience with internationally recognised hygienic-engineering principles.

The Principles of Hygienic Design in Food and Beverage Plants e-learning course available through the Diversey Hygiene Academy provides practical training for people involved in equipment selection, engineering, food safety, sanitation, maintenance and production.

You can also explore the topic in our on-demand webinar, Food Safety Starts with Hygienic Design, for practical insights into applying hygienic design principles to improve food safety and cleaning effectiveness.

Understanding hygienic design helps organisations move from repeatedly managing hygiene problems to preventing those problems by design.

Hein Timmerman

Global Sector Specialist F&B Lead & EHEDG President

Hein has held many roles covering Global Strategic Accounts support, training, technical, applications and solutions support. He is also the EHEDG President, an authorized trainer and chairman of the Working Group CIP, and is part of the International Dairy Federation taskforce on chemical residues.